Paco 7 automatic training fast & slow charging battery car 5am p 12v beak. This product sheet is originally written in English. Please find below a machine translation in French.
If you have any questions please contact us. Paco battery charger 5000ma 7 floors. We have 2 of these chargers in continuous use in our workshop and garages. Mainly used to maintain low-use vehicle batteries and recharge discharged batteries.
They have proven to be reliable, easy to use/supervise and can charge batteries quickly. We have also successfully recovered a number of batteries left unloaded for long periods - not always the case if the battery has a particular defect. Automatic loading in 7 steps: this is a fully automatic battery charger with 7 charging steps. The automatic charge protects the battery against overload, so the charger can remain connected to the battery indefinitely.The 7-step charge offers a complete and accurate charging process that gives the battery a longer life and better performance compared to the use of traditional chargers. De-sulphation: The de-sulphation stage can break down the sulfation that occurs in batteries that have been left for an extended period of time, bringing them back to a full load. Progressive start: a preliminary charging process that gently introduces battery power - it protects the battery and increases its life.
In bulk (constant current): the bulk mode charges the battery at the maximum rate (constant current) by putting a large amount of energy in the battery in a short time. This step will charge the battery to approx. 80% until the voltage reaches 14.4v for a load of 12v. The charge rate slows down so that the battery can absorb more energy and reach 100% charge.The voltage remains constant at 14.4 v for a load of 12 v while the current is gradually reduced until it is no longer possible to add power without overloading the battery. Battery test: An automatic battery test is performed immediately after the absorption phase. The test monitors the voltage for 90 seconds to see if the load has passed. Reconditioning: the battery reconditioning function is automatically started if the battery test fails (step 5). The reconditioning mode will then begin to introduce a low constant current for a period of 4 hours, then the charger will switch to floating load mode.
This reconditioning step can recover batteries from a deeply discharged state, increasing their performance and service life. The floating step keeps the battery at 100% charge without overloading or damaging the battery. This means that the charger can be left connected to the battery indefinitely. Input voltage: 220/240v - 50hz. Output power: 12 vdc - 5,000 ma.Minimum start voltage: 2 v. Fuse rating: 15a - 240v. Bulk: 5,000 ma (up to 14.4 v). Voltage to below 0.75a. Battery test: voltage monitored for 90 seconds. 0.75a - up to 16v - for 4 hours. Floater: 13.8 v with pulse function. Overvoltage: 17.5 v protected. Thermal protection: 65°C to -5°C. Cooling fan: automatic thermal protection. Combinations: lead acid 35-100 ah inc.
Charge time: 7 to 24 hours. Certification: this, cb, rohs, sgs and tuv. Use: car, boat, motorhome, motorcycle. To charge 12 v lead batteries only. The image shows what you will receive if you buy this item.Most of our lists have a number of postage options - please select the service you need before you purchase. Questions: We are happy to do our best to answer sensible and authentic questions during our normal office hours (Monday to Friday from 9:30am to 5:30pm), but please note that we do not have an intimate knowledge of all the brands and models or have no personal experience of assembly/use of all our products. The products are suitable only for the models indicated (if the products are suitable for other models, that is in our favour to say)! Products listed as universal mounting are not designed for a particular model.
The suggested templates are suitable for the listed product, but please check the specifications/sizes indicated - please understand what you purchase prior to purchase. Please allow us 24 hours to answer your question, if more than 24 hours have elapsed, please contact us again. Feedback: Please be reasonable - we do not like to give or receive anything other than positive comments. If you encounter a problem with your order, please contact us and give us the opportunity to correct the situation - errors occur, not often, but they occur. First of all, we want you to have a positive shopping experience and buy back from us.
Paco 5000ma 7 stage battery charge. Paco part no: mbc 1205. We have 2 of these loads in continuous use in our workshop and garages. Mainly used to maintain frequently used vehicle batteries and charging flat batteries.
They have proven reliable, easy to use/monitor and can charge batteries quickly. We have also successfully recovered a number of batteries left unloaded for long periods - not always the case if the battery has a particular fall.7 internship automatic charging: this is a full automatic battery charging with 7 charge interns. Automatic drawing protects the battery from being overloaded, so the charge can be left connected to the battery indefinitely. 7 stage charting gives a understanding and accurate charting process that gives the battery length life and better performance compared to using traditional loads. Desulphation: the desulphation stage may break down sulphation that occurs in batteries that have been left for an extended period of time, returning them back to full charge. Soft start: a preliminary charge process that just introduced power to the battery - this protectors the battery and increments it's life. Bulk (constant current): bulk mode charges the battery at the maximum rate (constant current) putting a large amount of power into the battery in a short amount of time. This internship will charge the battery to approx. 80% until the voltage reaches 14.4v for a 12v charge. The charge rate slows down so the battery can absorb more power and reach 100% charge. The voltage remains at a constant 14.4v for a 12v charge while the current is gradually reduced until no more power can be added without overcharging the battery. Battery test: an automatic battery test is conducted immediately after the absorption stage.
The test monitors the voltage for 90 seconds to see if the load was successful. Recondition: the battery reconditioning function is automatically initiated in case the battery fails the battery test (stage 5). Reconditioning mode will then begin to introduce low constant current for a period of 4hrs, then the load will go into float driving mode. This reconditioning internship can recover batteries from a recently discharged state increasing their performance and life.
The float stage maintain the battery at 100% charge without overcharging or damaging the battery. This means the charge can be left connected to the battery indefinitely. Input voltage: 220/240v - 50hz. Output power: 12vdc - 5000ma. Bulk: 5000ma (up to 14.4v).Voltage until below 0.75a. Battery test: voltage monitored for 90sec.
0.75a - up to 16v - for 4hrs. Float: 13.8v with pulse feature.
Over voltage: 17.5v protected. Thermal protection: 65°c to -5°c. Suits: 35-100ah lead acid inc. Certification: ce, cb, rohs, sgs & tuv.
Usage: car, boat, motorhome, motorcycle. For driving 12v lead acid batteries only. Questions: we are happy to do our best to answer sensitive, genuine questions during our normal office hours (mon-fri 09:30-17:30), how ever please note we do not have intimate knowledge of all made & models or have personal experience of fitting/using all our products.Products only fit models stated (if products fit other models its in our favor to say so)! Products listed as universal fitment are not designed for any one model. This item is in the category "auto, motorcycle - parts, accessories\ equipment, garage tools\testers, battery chargers\chargers, starters". The seller is "mattyzx" and is located in this country: gb. This item can be shipped to the following country: whole world.